Water & Wastewater Treatment

38 | MAY 2014 | WWT | www.wwtonline.co.uk In the know Getting to grips with trash screen installation Screen design and installation is crucial Correct trash screens design eases flood risk T rash screens form a crucial part of the infrastructure designed to reduce the risk of flooding in waterways and water processing sites. With considerable resources being employed in flood defence mechanisms to help protect property and maintain proper drainage across the country the performance of a humble trash screen is becoming increasingly important. Where a watercourse flows through a culvert there is an increased risk of blockage, requiring careful design con- sideration to ensure the most efficient structure is installed. A great deal of research has been carried out with regard to debris in watercourses and how to reduce its impact on the local environment. By understanding the seasonal variations, combined with the location, it is pos- sible to assess the likely flood risk and therefore decide on the best course of action with regard to protecting culverts and drains from blocking. A culvert represents a bottle-neck in a watercourse and o•en the installation of a trash screen will help to alleviate blockages, but the screen can also present a flood risk itself if it is not properly main- tained and cleared regularly. The amount and type of debris that is captured by the screen is dependent upon the time of year and the location of the screen. While it may seem obvious that screens are more likely to block during the winter months when there is more Jamie WeSley COMMERCIAL MAnAgER ECS EngInEERIng SERvICES 1. Trash screens form a crucial part of the infrastructure designed to reduce the risk of flooding in wa- terways and water processing sites rain, combined with fallen leaves and other vegetation, research has also shown that specific local conditions and the type of land use are also major factors that need to be considered. These factors all have a bearing on the amount and type of debris that is deposited in the watercourse and there- fore they also affect the risk of blockage and subsequent flooding. manufacture and installation Having decided on the design and the control specifictions, the time comes for the manufacture and installation, all of which needs expert engineering capabilities as well as experienced on-site engineers and divers who can complete both the civil engineering requirements as well as the mechanical and electrical engineering. ECS Engi- neering Services has a dedicated Water Control engineering division, which has over 20 years experience in delivering turnkey projects for clients including the Environment Agency, water utilities and internal drainage boards. automation For situations where the amount of debris demands regular clearing or for locations where manual intervention is not appropriate, it is possible to install an automated trash clearing system, which can provide efficent and regular removal of the debris. There are a num- ber of manufacturers and designs avail- able, each with its own advantages, depending on the specificapplication. One example is the rotating rake, which uses a chain drive to power the revolv- ing rakes to remove large amounts of debris from the bottom of the screen in an upward movement and discharging it at the top of the screen, possibly into a conveyor or hopper. These systems are better suited to narrower channels and are capable of removing large amounts of debris in a short time period.Another example removes the moving parts from the watercourse and uses a hy- draulically powered grab, which is sus- pended from a monorail and lowered into the water. As the grab is lowered it self-aligns with the bars of the screen and travels to the bed of the water- course at which point the grab is closed and the trapped debris is li•ed clear of the screen before being deposited in a waste skip. In applications where an automated system is being installed, the system can be triggered by a number of determining factors. Since the primary purpose of these structures is water level control, this can be detected and measured by ultrasonic devices and when the level differential either side of the screen reaches a certain point the clearing device can be started. If the trash screen is designed to help protect a pumping system, the clearing device can be triggered by the pumps coming on line to ensure that sufficent flw is permitted through the screen while the pumps are active. Finally, it may also be appropriate to have a timer to trigger the clearing system, especially if the watercourse has increased flaws at specific times of day. To see a video of a fully automated trash screen debris removal system, visit www.ecsengineeringservices.com www.wwtonline.co.uk | WWT | MAY 2014 | 39 2. However, the screen can present a flood risk itself if not properly maintained and cleaned regularly 3. This automated trash screen uses a hydraulically powered grab to clear locations where manual intervention is not appropriate • Factors affecting design ● Once the decision to install a screen has been made, proper design of the screen is essential in order to prevent it becoming a flood risk itself. This design should include careful consideration of the bar spacing, screen angle and distance from the culvert entrance in addition to the clearance method and frequency. ● Information gained about the location helps to deter- mine the type and size of debris likely to accumulate at the screen and, as the ratio of debris length to bar spacing increases, so does the risk of blockage. This can be combined with data relating to average flow rates, which also influence the risk of blockage. ● The angle at which the screen is installed also affects the efficiency, with some screen bar angles in common use having been shown to block more frequently. Once the design of the screen is finalised, it is then necessary to assess the maintenance requirements of the screen, based on the debris loading and frequency of cleaning required. ● Manual clearing will be sufficient in many situa- tions, in which case screen design must include a safe platform to minimise risk for the operative remov- ing debris from the scree. However, some cases may warrant an automated raking system that can operate round-the-clock to ensure the screen does not become blocked. Automation ● For situations where the amount of debris demands regular clearing or for locations where manual intervention is not appropri- ate, it is possible to install an automated trash clearing system, which can provide efficient and regular remov- al of the debris. There are a number of manufacturers and designs available, each with its own advantages, depending on the specific application. ● One example is the rotat- ing rake, which uses a chain drive to power the revolv- ing rakes to remove large amounts of debris from the bottom of the screen in an upward movement and discharging it at the top of the screen, possibly into a conveyor or hopper. These systems are better suited to narrower channels and are capable of removing large amounts of debris in a short period. ● Another example removes the moving parts from the watercourse and uses a hydraulically pow- ered grab, which is suspend- ed from a monorail and low- ered into the water. As the grab is lowered it self-aligns with the bars of the screen and travels to the bed of the watercourse at which point the grab is closed and the trapped debris is li ed clear of the screen before being deposited in a waste skip. ● In applications where an automated system is being installed, the system can be triggered by a number of determining factors. Since the primary purpose of these structures is water level control, this can be detected and measured by ultrasonic devices. When the level differential either side of the screen reaches a certain point the clearing device can be started. ● If the trash screen is designed to help protect a pumping system, the clear- ing device can be triggered by the pumps coming on line to ensure that sufficient flow is permitted.

• Cover